Maple Wood Staining

Because maple has such tight grain pigment type stains dont soak into the wood except where there is a spot with more open grain as you found out. Immediately take a dry.

Wood Stain General Finishes Honey Maple Rockler Woodworking Tools

With hard woods like maple even soft maple is pretty dense pigmented stains generally work best if you are seeking only a light to moderate shade.

Maple wood staining. Stir the can thoroughly to evenly redistribute any color pigments that may have settled to the bottom. Rendering it even less able to absorb the stain than if you had stopped sanding at 180 or 220 grit. Sanding the wood to 600 grit exacerbated the problem by burnishing the surface of the wood.

Dyes work better but limit the colors available. When applying a stain be sure to use a pre-stain conditioner to try and even out the blotchy patches that tend to appear. Staining maple to a dark hue which is very dense and quite light in color with an oil based or gel-style product is hard work.

Try using dyes such as TransTint or Transfast. Before staining or painting maple wood you should create a mixture of linseed oil and turpentine in like proportions. Test any stain you are considering.

White birch will finish as a low density wood and be quite absorptive. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new. Hard maple is so dense that the finishes do not soak in nearly as well.

Staining close-grained woods like maple and cherry presents a problem for the wood finisher because they can absorb regular penetrating stains unevenly and appear blotchy. And in my opinion not a good idea. Then take an old towel and rub the entire surface of the maple wood that is to be painted with the mixture.

Stains tend to fill pores cracks and crevices in wood. The same goes for lacquers the solvent based will enhance the grain and depending on the type may or may not yellow. Staining maple is generally not recommended by finish manufacturers since the dense grain does not allow the penetration of most pigments.

Maple is a closed grain wood this means the wood does not like accepting anything into its pores which includes stain. To get the wood to accept stain there is a popular method of water popping the grainWater popping is the method of actually putting water evenly on the floor to raise the grain. If you have determined that you need to change the color of maple wood youll need to make sure that you properly prepare the wood before painting.

There are other brands as well often marketed as aniline dyes. Some blotchiness with hard maple. Apply Minwax Pre-Stain Wood Conditioner to ensure an even stain color see Wood Preparation for other tips.

As with other hardwoods such as cherry maple can be a bit temperamental to finish particularly when staining. Maple is a difficult wood on which to achieve uniform stain and the appearance can look as. Preparing the maple for stain is easy finish sand down to 400 grit going with the grain of the wood as you sand.

This wont completely solve the problem though. This week I done some more testing with stains this time I tested them on Soft Maple wood. PART 1three steps in staining maple doors.

I hope this helps somebody thats looking to stain Maple. Stir the can thoroughly. Oil based poly will yellow and waterbased poly is IMHO too insipid for maple.

To get darker you would need to begin with a dye. Maple like several others species such as walnut American cherry pine and Douglas fir do not take stain as evenly as species such as red oak and white oakBlotchy color can result from other factors as well such as inconsistent sanding procedures water-popping or stain application. Wet the wood with water before staining and let dry this opens the grain to accept the stain evenly then sand out with 320 grit going with the grain.

Maple Versus Birch A comparison of the finishing characteristics of Hard Maple and White Birch. Waterbased lacquers will generally look like the wb poly although there are brands out there that have an amber tone and can look pretty nice. You should look for a powdered water soluble dye.

Maple Cabinet Door Staining Problems Solutions When staining soft maple Kitchen doors and drawers from a millworks shop the painter applied a special walnut stain directly to the raw wood. The stain did not take well on wood milled with the grain and on cross cuts the stain soaked into the wood giving a. With dye you control the intensity of the color by the concentration of the dye solution.

Stain and let sit for 24 hours.

Varathane 8 Oz Colonial Maple Classic Wood Interior Stain 4 Pack 339731 The Home Depot